A dripping faucet is a small leak with a large annual total. A drip every second can waste thousands of litres in a year, stain a sink, and keep you awake. Most drips are a worn washer, a worn O-ring, or a worn cartridge — inexpensive parts — and not a reason to replace a whole fixture. The work is methodical: shut the water off, identify the faucet type, change the sealing parts, and put it back without scarring the finish.
Shut the water off at the supply valves under the sink, or at the house main if those valves will not turn. Open the faucet to drain the line and confirm it is off. If a shutoff is frozen, crumbling, or starts to leak when you touch it, stop and call a licensed plumber; a broken angle stop can flood a cabinet in seconds. Place a towel and a small bucket in the cabinet. Put the stopper in, or cover the drain, so a dropped screw does not start a second job: unclogging the drain.
Identify the faucet before you buy parts
Look under the handle and at the spout. Most household faucets are one of four designs:
- Compression. Two separate handles, often older. Each handle screws a stem down onto a rubber washer. A drip is usually that washer, or the seat it presses against. You will feel many turns from off to on.
- Cartridge. One or two handles that move a set angle, often a quarter turn. A cartridge inside the body is the valve. Drips and a stiff handle are usually the cartridge or its O-rings.
- Ceramic disc. A single lever, often with a wide cylindrical body. Two ceramic discs inside a cartridge seal against each other. These are reliable until grit scores them.
- Ball. A single, often rounded, handle over a metal or plastic ball — a style long associated with some Delta kitchen faucets. Seals and springs around the ball wear and are sold as a small kit.
If you can, lift the handle and look for a brand name. Take the old cartridge or washer with you to the hardware store, or photograph the parts in order on a towel. "A kitchen cartridge" is not a useful description; there are dozens.
Compression faucets: washers and seats
With the water off, pry off the decorative cap, undo the handle screw, and lift the handle. Unscrew the packing nut and lift the stem out. At the bottom of the stem is a small rubber washer held by a screw. Replace the washer with one of the same size and thickness, and add a drop of plumber's grease on the threads and the new washer.
Look down into the valve seat in the faucet body, using a flashlight. If the seat is pitted or rough, a new washer will only drip a little later. Some seats can be unscrewed with a seat wrench and replaced. If the seat is integral and badly worn, the whole faucet may be at the end of a long life.
If the leak is around the handle, not out of the spout, the packing or an O-ring on the stem is the usual cause. Replace those as a set while you are inside.
Cartridge, disc, and ball faucets
Cartridge. Remove the handle — often a hidden set screw on the side, needing a small Allen key — and any retaining cap or clip. The clip may be a U-shaped piece you pull with pliers. Twist and lift the cartridge. If it is stuck, a cartridge-puller tool for that brand is cheaper than a ruined faucet body. Note the orientation; many cartridges only go back one way, or they will swap hot and cold.
Take the cartridge with you and buy the match, plus new O-rings if they are not included. Clean the housing gently. Lightly grease the new O-rings with plumber's grease, not petroleum jelly, which can damage some rubbers. Seat the new cartridge, replace the clip, and reassemble.
Ceramic disc. The steps are similar: remove the handle and cap, lift the disc cartridge, and replace it as a unit. Do not try to lap or "sharpen" the ceramic plates on the kitchen counter. Grit in the line is a common reason these fail, so also clean or replace the aerator at the tip of the spout when you are done.
Ball. There are usually a cap and a collar over the ball, and a set of rubber seats and springs underneath. Kits are inexpensive and include the small parts you will drop once. Photograph the order, replace the seals and springs, and do not overtighten the cap — tight enough to stop the leak, loose enough that the handle can still move.
Wrap the jaws of a wrench with tape or a cloth before you put them on a chrome nut. A single slip leaves a scar you will see every day. Approach nuts as if they were porcelain: snug, then a little more, not a long heave.
After it is back together
Open the supply valves slowly. Check under the sink as well as at the spout. Move the handle through its full range, including mixing, and look for drips at the spout, the handle, and the supply connections.
Unscrew the aerator (the screen at the tip), rinse the grit that the repair may have loosened, and put it back. A "drip" that is really a blocked aerator spraying sideways is a two-minute fix and is worth checking even when you came for a washer.
If the faucet still drips after a new cartridge or washer, the body or the seat may be damaged, or the part may be slightly wrong. Do not stack extra washers or crank a handle down harder as a daily habit. That destroys stems.
When the fixture itself is the problem
Some faucets have been repaired past the point of sense: a corroded body, a cracked plastic housing, a seized diverter on a tub-and-shower valve. A shower or tub valve inside the wall is a different and more serious job than a lavatory set on the sink. If you have to open a tiled wall to reach a leaking shower cartridge, and you are not confident, hire a licensed plumber. A leak that disappears into a wall is much more expensive than a visible drip in a sink.
Outdoor faucets have their own freeze-related failures. If the drip is on the side of the house, especially in autumn, deal with it as part of winterizing the tap so you are not leaving a cracked sillcock full of water.
A repaired faucet and a quiet toilet tank are two of the easier ways to stop wasting water without buying a new fixture. Take your time, keep the parts in order, and treat the finish as if it were softer than it looks.