A sticking door is annoying in July and a genuine problem in a house that has to close against winter air. The door may rub the floor or the head of the frame, catch at the latch, or close only if you lift the handle. The mistake is to start planing wood before you know why it sticks. Many sticking doors are hanging wrong: a loose top hinge, a worn screw hole, or a frame that has moved a little. Planing is sometimes the right last step, and it is a poor first one, especially on a solid door that will shrink again in January.

Canadian houses give you a useful clue. Wood swells in the humid season and shrinks when the heating system runs and the indoor air dries out. A door that sticks only in summer and frees itself in winter is often a swelling or paint-buildup problem. A door that sticks all year, or that suddenly drops after years of good behaviour, is often a hinge or a settling frame.

Safety

Support a heavy door if you take more than one hinge off, and do not plane toward your hand. If the frame itself is rotten, if the wall is cracked and still moving, or if an exterior door no longer keeps weather out after a careful adjustment, the job may be a carpenter's, not a half-hour of sanding. Do not plane a fire-rated door in a way that removes its rating or hardware clearances if that applies to your building.

Diagnose with a pencil and a slow close

Close the door slowly and watch the gap around it. A consistent, thin gap on the hinge side, the latch side, the top, and the bottom is the goal. Where the gap disappears is where it rubs. A pencil rubbed on the suspect edge will transfer onto the jamb and confirm the contact line.

Also try this: lift the handle or the latch edge as you close. If the door suddenly clears or the latch finds the hole, the door is sagging. The top hinge is the usual culprit. Tightening or replacing those screws will do more than a plane will.

Open the door and look at each hinge. Loose screws, a hinge pulled away from the jamb, or a knuckle that looks out of line are all evidence. If the door also squeaks, quiet the hinge after it is tight; the method is in how to stop a door from squeaking.

Fix sagging at the hinges first

Tighten every hinge screw with a bit that actually fits. If a screw spins, the hole is stripped. Do not put a matchstick and hope if you can put a longer screw instead. On the jamb side of the top hinge, one or two 50 to 75 millimetre (2 to 3 inch) wood screws, driven carefully into the framing behind the jamb, will often pull the whole door up and in. Drive them straight and stop if you feel the jamb starting to pinch or if a screw is about to break out through a visible casing.

If the hinge leaves no longer sit flush, a thin cardboard or wood shim behind one leaf can tilt the door a little in the useful direction. This is a subtle adjustment. A thick shim will create a new rub somewhere else.

Paint glued into a hinge or built up on the edge of the door can make a "swollen" door that is really a thicker door. Score the paint at the moving joints, and if the edge is caked, sand the paint buildup before you cut into bare wood.

Tip

If you do plane or sand, mark the high spot, remove a little, then hang and test. You can always take more off. You cannot put a shaving back, and a door you over-planed in August may rattle and leak air in February.

When the latch misses the strike

Sometimes the door closes but will not latch, or you have to slam it. Look at the strike plate on the jamb. A bright mark shows where the latch is hitting. If it misses high or low by a couple of millimetres, you can often enlarge the strike opening with a file, or move the plate slightly, rather than taking wood off the door.

If the miss is large, the door is sagging or the frame has shifted, and you are back to the hinges or to a carpenter. Forcing the latch by leaning on the door every day will wear the latch and loosen the plate.

A strike that no longer meets an exterior door's weatherstripping, or a door that closes only by crushing the weather seal, should be adjusted with weather in mind. You want a firm seal without a running shoulder-charge to get it latched on a -20°C evening.

Swelling, paint, and a careful plane

If the hinges are tight, the door is hanging square, and it still rubs in a clearly marked place, you can remove a little material from that edge. Take the door off only if you need to, supporting it so the corners do not break. A sharp hand plane or a sanding block along the length of the edge, following the existing bevel if there is one, is easier to control than a power planer for a first attempt.

Stay off the face of the door. Work the hinge-side or latch-side edge in long, light passes. At the top, a little off the high corner may be enough. At the bottom, confirm you are not about to split a thin veneer, and think about flooring: a door that suddenly sticks after new carpet or a new rug is a clearance problem, and the cure may be trimming the bottom or changing the floor covering, not attacking the latch.

Seal any raw wood you expose with paint or varnish that matches the door, including the top and bottom edges if you can reach them. Bare wood on an edge is a sponge for the next humid season, and it will swell right back.

Seasonal habits, and when to stop

In a tightly humid summer, run the bathroom fan, use a dehumidifier if the house feels damp, and do not plane a door on the most swollen day of the year to a clearance that will look like a canyon in January. In winter, a door that rattles may only need a strike adjustment or a weatherstripping tweak, not a new door.

If the frame is visibly out of square, if there are new cracks in the drywall at the corners of the opening, or if several doors in the house have started to bind at once, the house may be moving. A single sticking interior door is usually local. A pattern is worth a closer look, and sometimes a professional opinion, before you keep cutting wood.

Once the door swings and latches without a fight, you are done. If you chipped the wall or the jamb while you were working, a tidy drywall or trim patch will make the repair disappear. A door that closes cleanly is quieter, kinder to its hinges, and — on an exterior opening — part of how the house holds its heat when the wind comes down the street.