Drywall looks fragile when it is broken, and it is forgiving if you give a patch enough thin coats and enough drying time. Most visible scars come from rushing: one thick blob of compound, a proud screw head, or paint on raw paper. This guide covers the three sizes you actually meet in a house — a nail pop or ding, a fist- or doorknob-sized hole, and a larger broken section — on an ordinary interior wall.

It does not cover a wet or mouldy wall, a ceiling that is sagging, or a hole that cuts into electrical or plumbing. Those are different jobs.

Safety

Before you cut, find out what is behind the wall. Use a non-contact voltage tester around the area, look for nearby switches and outlets, and be cautious on a line between a bathroom and a kitchen, or anywhere a pipe might run. If you hit a wire or a pipe, stop. Do not cut into a wet, stained, or crumbling wall until you know why it is wet; a pretty patch over an active leak will fail and can hide damage. If the board is damp or you see mould inside the cavity, fix the moisture first and hire help if the area is large.

What you need, and what you can skip

For a small ding you need a putty knife, a little all-purpose joint compound or a lightweight spackle, and 150-grit sandpaper. For a hole you can add a self-adhesive mesh patch or a scrap of drywall, a handful of drywall screws, and paper or mesh tape. A cheap drywall saw or a sharp utility knife will cut the opening square.

You do not need a 20-litre pail of professional mud for one hole. A small tub of all-purpose compound is enough. Premixed compound is easier for occasional work than powder you mix yourself. Keep a damp cloth handy; dried crumbs on the floor become white dust later.

A good basic tool kit already covers the knife, screwdriver, and drill. Buy the patch materials for the job.

Nail pops, dents, and torn paper

A nail pop is a small crater or bump where a nail or screw has pushed the paper out, often as a house dries through a Canadian winter. Do not just smear compound over a proud fastener — it will come back.

Press around the bump. If you feel a fastener, drive a drywall screw 4 or 5 centimetres above or below it, into the stud, until the head is just dimpled below the paper, not punching through. Then set or remove the old nail. Slice off any loose paper. Fill the dimples with a thin coat of compound, let it dry, then a second thin coat slightly wider than the first. Sand lightly. The paper face of drywall pills if you sand too hard; stop when the filler is flush, not when you have polished a bald spot.

For a dent with intact paper, a wipe of compound is enough. For torn paper, tear away the loose bits, seal the fuzzy edge with a thin smear of compound or a dab of primer, then fill. Raw fuzzy paper will bubble under paint if you skip that step.

A hole you can cover with a patch

For a hole up to about 10 centimetres — a doorknob knock, a small accident — a self-adhesive mesh patch is honest, fast work. Trim any broken gypsum so the edges are fairly sound. Stick the mesh so it overlaps the good wall on all sides, then fill the mesh with compound, pressing it through the holes. Let it dry thoroughly. Canadian houses in winter can be dry and warm inside, which helps, but a thick first coat will still shrink and crack. Prefer two or three thin coats, each a little wider, feathered out onto the wall.

If you would rather use a scrap of drywall (a "California patch" or a plug with a paper border), cut a square slightly larger than the hole, score the back, and peel the gypsum away so you have a paper flange around a plug that fits the hole. Butter the flange with compound, set it in, and treat the paper like tape. It takes a little more patience and leaves a slimmer repair.

Sand between coats only enough to knock down ridges. Wipe the dust before the next coat or it will mix into the mud and leave grit.

A larger hole needs backing

Once a hole is bigger than a mesh patch can honestly span — say a long broken section, or a cut-out for a forgotten box — you want a square opening and something for a new piece of board to screw to.

Draw a neat rectangle around the damage, cutting back to sound board. A drywall saw or a knife and a straightedge will do. If you can, cut to the centre of the nearest studs so the new piece has solid wood on two sides. If the hole sits between studs, slip a short piece of 1x lumber inside the cavity, spanning behind both sides of the opening, and screw through the existing drywall into that backing. Watch for wires as you work.

Cut a new piece of 12.7 mm (1/2 inch) board — or 15.9 mm (5/8 inch) if that is what the wall is — to fit the opening with a little breathing room, not a fight. Screw it to the studs or the backing, dimpling the heads. Tape every joint with paper tape or mesh, embed the tape in compound, and build two or three feathered coats. The wider and thinner the last coat, the less you will see the rectangle later.

Tip

If the surrounding wall has texture — orange peel or knockdown — a perfectly smooth patch will advertise itself after painting. Practice texture on a scrap of cardboard. A light splatter from a texture spray, or a stipple with a brush flicked at the surface, is easier to blend than you might think, but it has to happen before the final prime and paint, not after.

Prime, then paint

Joint compound is thirsty. If you paint straight over it, the patch will flash — a dull, slightly different sheen — even when the wall feels smooth. Sand, wipe, and prime the repaired area with a drywall primer or a sealer-primer, then paint the whole wall if you can, or at least a corner-to-corner section, with the same sheen as the rest of the room.

Colour matching is its own small problem. A leftover can from the original job is ideal. If you do not have it, take a chip (from behind a switch plate if possible) to the paint desk. Even a good match can look slightly off in a small island of new paint, which is why painting a full wall is often the quieter finish.

Special cases

Bathrooms and laundry rooms should be patched with moisture-resistant board if you have cut into that type of wall, and the room still needs to dry properly after showers. A patch will not save a wall that is being wet from behind; if the damage is near a tub, confirm the tub caulk is actually sealing, and look for leaks before you close the wall.

Outside corners often have a metal or plastic bead. If the bead is crumpled, replace that section of bead rather than piling compound into a dent. It takes more cutting, and the result looks like a corner again instead of a lump.

Ceilings are the same process with worse arms and a higher cost of a mistake. Support a large ceiling patch properly; do not rely on tape alone to hold a heavy piece over your head.

If the "hole" is actually a door that has been striking the frame and chipping the finish, fix the door's fit as well as the wall: how to fix a sticking door. Otherwise you will patch the same dent twice.