Dark lines in shower grout are often mildew or surface mould sitting in a porous material that never quite dries. They can also be ordinary soap scum, hard-water staining, or — less often — a sign that water has been getting behind the tile. The cleanup is a careful cleaning job plus a drying habit. It is not a reason to mix every bottle under the sink, and it is not something to ignore if the problem is large, smelly, or making people in the house unwell.

This guide is for ordinary spots and lines on shower grout and nearby silicone. It is not a guide to tearing out a tiled wall or to remediating a contaminated basement.

Safety

Ventilate the room. Wear gloves and eye protection. Never mix bleach with vinegar, ammonia, or acidic cleaners — the combination can release dangerous gas. If you already used one product, rinse it away completely and let the surface dry before you consider another. If mould covers a large area (often described as bigger than about one square metre), if you can see or smell it inside a wall, or if anyone in the home has serious respiratory issues, hire a professional rather than turning the bathroom into a chemistry project.

Decide what you are looking at

Soap scum is usually a dull, greasy film, often beige or grey, and it sits on top of tile as much as on grout. It comes off with a soap-scum cleaner or a paste of baking soda and a little dish soap, and it does not need bleach.

Hard-water stains are crusty and whitish or rusty, especially around a shower head or a corner that never quite rinses. Those are mineral deposits. Acidic cleaners can help on ceramic tile, but they can etch natural stone, some grouts, and some finishes. If you have marble, limestone, or a stone-look material you cannot identify, do not use vinegar or a strong acid.

Mould or mildew in grout tends to be speckled or veined, often black, dark grey, or sometimes pinkish, and it returns quickly if the joint stays damp. Surface staining in the pores of the grout is common and usually cleanable. If the tile is loose, the grout is crumbling out in chunks, the wall feels soft, or the stain keeps blooming in the same map after a genuine cleaning, you may have water behind the tile. Cleaning the face will not fix that.

Start with the mildest method that works

Dry-clean first: a dry brush will remove a surprising amount of loose soap and rust-coloured scum so you are not turning it into mud.

Then try a paste of baking soda and a little water, worked into the grout with an old toothbrush or a stiff grout brush. Let it sit ten or fifteen minutes, scrub, and rinse. For many light jobs, that is enough.

If the stain remains, 3% hydrogen peroxide from a pharmacy is a useful next step on grout. Spray or dab it on, let it sit (ten to fifteen minutes is a reasonable start), and scrub. It is gentler on many surfaces than household bleach and does not leave the same fumes, but it can still lighten some coloured grouts and fabrics, so test a low corner first and keep it off towels you care about.

Oxygen bleach (sodium percarbonate), sold as a colour-safe powder you mix with warm water, is another option for stubborn organic stains. Mix as the label says, apply, wait, scrub, and rinse well. Do not confuse it with chlorine bleach, and do not mix them.

Tip

A cheap plastic grout brush, used on a slightly damp joint, beats a metal brush or a grinder. Wire and rotary tools chew grout out of the joint and leave a trench that collects more dirt than before.

About vinegar, bleach, and steam

White vinegar is a folk favourite. It can help with soap film and some minerals on plain ceramic tile, and it is the wrong first choice on natural stone and on some grout sealers. If you use it on ceramic, do not follow it with chlorine bleach, and rinse thoroughly.

Chlorine bleach can lighten mould stains on grout, and it is still sold for that job. If you use it, ventilate as if you mean it, wear eye protection, use it diluted according to the label, keep it off skin and off metal drains if you can, and never mix it with other cleaners. Many people can clean an ordinary shower without it by being patient with peroxide and a brush. If you do use bleach, rinse it away completely when you are done.

Steam cleaners are sometimes advertised as a grout miracle. Steam can help loosen film, and it can also drive moisture into cracked grout and into poorly sealed corners. If you use steam, keep it moving, do not press a jet into a cracked joint, and dry the room afterwards. Do not steam a wall you already suspect is wet inside.

Rinse, dry, and seal

Rinse until the joint no longer feels slippery or soapy. Then dry the grout on purpose: a towel, the exhaust fan, and, if needed, a small fan aimed at the shower. The cleaning is only half the work. Mildew comes back when the joint stays damp for hours after every shower.

Once the grout is fully dry — give it a day if you can — a penetrating grout sealer can slow down the next round of staining. Apply it only to grout, wipe haze off the tile, and respect the cure time. Sealer is not a waterproof tank; it is a delay. Reapply according to the product, often once a year in a hard-working shower.

If the dark line is actually in the silicone around the tub, you can sometimes clean the surface, but mildew that has grown through old, porous caulk often means the bead should be cut out and replaced. Recaulking over a stained, failing bead traps the problem.

Change the room, not just the grout

Canadian bathrooms, especially in tight, well-insulated houses and in winter when windows stay shut, can hold steam for a long time. Use the exhaust fan during the shower and for at least twenty minutes after, and confirm the fan actually vents outside rather than into an attic. A squeegee on the walls after a shower takes under a minute and does more than most products. Leave the shower door or curtain open so the stall can dry. Fix drips: a constantly wet corner from a leaking shower head or a dripping tap is a greenhouse.

If the fan is noisy and weak, cleaning the cover and confirming the duct is not crushed is a fair homeowner job. Replacing a fan, or running a new vent, may be more than you want to take on, and electrical work should follow the same licensed-pro rule as any other circuit.

When cleaning is the wrong tool

Stop and get help if grout falls out in pieces, tiles rock, the wall or floor feels soft, stains return in a widening map, or you find mould on the ceiling, in the exhaust fan, or on the other side of the wall. Those are moisture-intrusion problems. They may involve a failed tub membrane, an unsealed corner, or a leak from a fixture. Opening a tiled shower without a plan can make a contained problem worse.

For everyday dark grout, though, a mild cleaner, a real brush, a dry room, and a fresh bead of caulk where the old one has failed will take care of most of what people mean when they say their shower "has mould." Be patient, do not mix products, and let the room dry as if that were the main repair — because it is.